Volkswagen Golf Service & Repair Manual: 2-pack HS Performance clear coat
2-pack HS Performance clear coat -LZK 769 K06 A5- |
2-pack HS Performance clear coat is a high-gloss, VOC
compliant, high-solid clear coat. |
Flexible application in all areas of repair |
Flexible application in one-and-a-half spray coats
(preferred) or two coats (possible) |
Good gloss and filling power |
|
|
|
2-pack VHS hardener -LHA 009 051 A2-/-LVM 009 051 A5- |
2-pack VHS hardener, fast-drying -LHA 009 050 A2- |
2-pack VHS hardener, slow-drying -LHA 009 052 A2-/-LHA 009
052 A3- |
2-pack VHS hardener, extra slow-drying -LHA 009 053 A2- |
The choice of hardener depends on the temperature and size
of the surface. See technical data sheet for 2-pack VHS hardener
→ Chapter. |
For elasticization, see
→ Anchor |
Clear coat additive -LVM 007 000 A2- |
HS spot thinner -LVM 006 000 A2- |
See technical data sheet for 2-pack HS spot thinner
→ Chapter |
|
|
|
Application time/pot life: |
– |
Mixed for spraying, 60 to 120 minutes at +20°C |
|
|
|
Method of application: “spray”. |
|
|
|
– |
Application viscosity 4 mm, +20 °C, DIN 53211 |
Application viscosity 4 mm, gravity-feed spray gun
“compliant” and “HVLP”. |
|
|
|
Add 5% clear coat additive -LVM 007 000 A2- at a material
temperature of +20 °C |
Note
When used as clear coat for spot repairs (Clever Repair
method), the 5% clear coat additive -LVM 007 000 A2- may be
replaced with 5% HS spot thinner -LVM 006 000 A2-. |
The mixture described here for the Clever Repair method must
not be used on horizontal surfaces. |
– |
If thinner is added, use measuring stick to mix. |
|
|
|
– |
Adjust spray nozzle following manufacturer's instructions to
1.3-1.4 mm for “compliancy”. |
– |
Adjust spray nozzle following manufacturer's instructions to
1.3-1.4 mm for “HVLP”. |
– |
Adjust spray pressure following manufacturer's instructions
to 2.0-2.5 bar for “compliancy”. |
– |
Adjust atomising pressure following manufacturer's
instructions to 0.7 bar for “HVLP”. |
|
|
|
Can be applied in one-and-a-half coats; that is, the first
half coat forms a thin, nearly uniform film, upon which a
complete, uniform coat is sprayed. |
Apply in two spray coats with 5-10 minutes intermediate
flash-off time The first coat is applied with restraint, but
still uniformly. |
– |
The specified thickness for the dry film is 50-70 µm. |
|
|
|
Air drying at +18 to 22 °C ambient temperature: |
|
|
|
Final flash-off time with force drying is at least
5-10 minutes. |
|
|
|
Force drying at +60-65 °C material temperature in
25-35 minutes. |
|
|
|
Final flash-off time with infrared drying is at least
5-10 minutes. |
|
|
|
Infrared drying with short-wave radiant heater,
10-15 minutes |
|
|
|
Elasticization of rigid and semi-rigid plastics: |
First mix the base material with 15% elastic additive -ALZ
011 001-. |
Mixture with 2-pack VHS hardeners, 3:1 with 5% clear coat
additive -LVM 007 000 A2- (drying time increases). |
|
|
|
Personal protective equipment: |
Adhere to the safety data sheet. |
Wear personal protective equipment during application. |
|
|
|
Flash point: |
Above +23 °C |
VOC content:
2004/42/IIB(d)(420)420 |
The EU limit value for this
product (product category IIB.b) in ready-to-spray form is max. 420 g/l
of volatile organic compounds. The VOC content of this product in
ready-to-spray form is max. 420 g/l. |
2-pack HS Brillant plus clear coat -LZK 769 K05 A5-, 48
months from production date. |
Clear coat additive -LVM 007 000 A2- 24 months from
production date. |
May be used until the date stated on the label at latest if
stored in sealed original containers at +20 °C. |
|
|
|
Designation:
2-pack HS Brillant plus clear coat -LZK 769 K05 A5-
Issued 02.2012
Product description
...
Designation:
Blender -LVE 013 100 A2-
Issued 10.2012
Product description
Blender ...
Other materials:
Minimum curing periods for bonded windows
WARNING
There are special requirements for renewing bonded
windows. One of these standards is, for example, that a
freshly bonded windscreen must comply with the safety
requirements, even in an accident, fo ...
Cleaning windows and exterior mirrors
First read and observe the introductory information
and safety warnings Cleaning windows and exterior mirrors
Moisten the windows and exterior mirrors with commercially available, alcohol-based
glass cleaner.
Dry the glass surfaces with a clean chamois leather or a lint-free cloth. Chamois ...
Bleeding coolant circuit of auxiliary heater
The removal and installation procedures for the auxiliary
heater and the circulation pump -V55- described in this Workshop
Manual ensure that only a small quantity of air enters or
remains in the coolant circuit. Therefore it is not necessary to
bleed th ...
© 2016-2024 Copyright www.vwgolf.org